Applied-motion PDO5580 Manual do Utilizador

User’s ManualPDO 5580Step Motor Drivermotors • drives • controlsPDO 5580Step Motor Driver50% IDLEJOYSTICKEXT SPEED0.20.40.81.62.0CURRENTHIGH SPEEDLOW

-10-Sourcing LogicIf your controller has STEP, DIR and GND (ground or common) outputs, connectSTEP- and DIR- to GND. Connect STEP+ to STEP. Connect

-11-200STEPS/REV(FULL)MICROSTEPRESOLUTIONMICROSTEPRESOLUTIONMICROSTEPRESOLUTIONMICROSTEPRESOLUTIONMICROSTEPRESOLUTIONMICROSTEPRESOLUTIONMICROSTEPRESOL

-12-Joystick ModeIn this mode, speed and direction are determined by the voltage applied to the WPR(wiper) terminal. 2.5 volts is “stopped” (no speed

-12-Joystick ModeIn this mode, speed and direction are determined by the voltage applied to the WPR(wiper) terminal. 2.5 volts is “stopped” (no speed

-11-200STEPS/REV(FULL)MICROSTEPRESOLUTIONMICROSTEPRESOLUTIONMICROSTEPRESOLUTIONMICROSTEPRESOLUTIONMICROSTEPRESOLUTIONMICROSTEPRESOLUTIONMICROSTEPRESOL

-10-Sourcing LogicIf your controller has STEP, DIR and GND (ground or common) outputs, connectSTEP- and DIR- to GND. Connect STEP+ to STEP. Connect

-9-Setting up For Pulse & Direction ModeYou must:✔ Connect an indexer/controller to the Step and Direction inputs.✔ Set the steps/rev.✔ Turn of

-8-SELF TEST6OSC BYPASS5Pulse & Direction ModeSELF TEST6Self Test ModeModes of OperationThe PDO 5580 has four modes of operation, selected by thre

-7-Eight lead motors can also be connected in two ways: series and parallel. Aswith six lead motors, series operation gives you more torque at low s

-6-A+A–NCB+B–NC6leadmotorRedBlackRed/WhtGreenGrn/WhtWhiteA+A–NCB+B–NC6leadmotorGrn/WhtWhiteGreenRedRed/WhtBlack6 Leads Series Connected 6 Leads Center

-2-IntroductionThank you for selecting an Applied Motion Products motor control. We hope ourdedication to performance, quality and economy will make

-5-Installing an AC Line CordRemove about 5 mm (3/16 inches) of insulation from each of the three wires of yourline cord. (That’s right, three wires.

-4-Before you can change the 110/220 volt switch setting, you must remove the motorconnector and the AC power connector from the drive. Set the drive

-3-Getting StartedTo use your Applied Motion Products motor control, you will need:✔ a power cable (line cord)✔ a compatible step motor (see page 21)✔

-2-IntroductionThank you for selecting an Applied Motion Products motor control. We hope ourdedication to performance, quality and economy will make

User’s ManualPDO 5580Step Motor Drivermotors • drives • controlsPDO 5580Step Motor Driver50% IDLEJOYSTICKEXT SPEED0.20.40.81.62.0CURRENTHIGH SPEEDLOW

-3-Getting StartedTo use your Applied Motion Products motor control, you will need:✔ a power cable (line cord)✔ a compatible step motor (see page 21)✔

-4-Before you can change the 110/220 volt switch setting, you must remove the motorconnector and the AC power connector from the drive. Set the drive

-5-Installing an AC Line CordRemove about 5 mm (3/16 inches) of insulation from each of the three wires of yourline cord. (That’s right, three wires.

-6-A+A–NCB+B–NC6leadmotorRedBlackRed/WhtGreenGrn/WhtWhiteA+A–NCB+B–NC6leadmotorGrn/WhtWhiteGreenRedRed/WhtBlack6 Leads Series Connected 6 Leads Center

-7-Eight lead motors can also be connected in two ways: series and parallel. Aswith six lead motors, series operation gives you more torque at low s

-8-SELF TEST6OSC BYPASS5Pulse & Direction ModeSELF TEST6Self Test ModeModes of OperationThe PDO 5580 has four modes of operation, selected by thre

-9-Setting up For Pulse & Direction ModeYou must:✔ Connect an indexer/controller to the Step and Direction inputs.✔ Set the steps/rev.✔ Turn of