Applied-motion 2035 Manual do Utilizador descarregar pdf

Flip Over

Connecting the Motor

STEP motors have 4, 6 or 8 leads , these are

wired to 4 connections on the drive in various

combinations.

Motors will perform differently according to the way

it is connected. To nd out more about the different

ways of connecting your motor, see the specs or

FAQs on our website.

Warning: When connecting the motor to the driver, be sure that the motor

power supply is off. Secure any unused motor leads so that they can’t short

to anything. Never disconnect the motor while the drive is powered up. Never

connect motor leads to ground or to a power supply!

Connecting Logic

A schematic diagram of the input circuit is shown below.

Connect your logic circuitry to the signal connector as

shown in the sketch at the right. Even though the drive

provides it’s own 5 volt logic power, you must supply 5-24

volts DC to activate the LEDs on the input side of the

optoisolators. Most CMOS and open collector TTL devices

are directly compatible with this drive. If you are using

open collector outputs, no pull up resistor is necessary.

STEP tells the driver when to move the motor one step.

DIRECTION signals which way the motor should turn.

ENABLE allows the user to turn off the current to the motor by setting this signal to

logic 0.

If you have no need to disable the ampliers, you don’t need to connect any-

thing to the ENABLE input.

Connecting to a controller with a differential output

Connecting to controller with a single ended output

Is This the Right Manual?

3 terminals - old 2035 or 2035 O. This is the wrong manual.

4 terminals - new 2035. This is the right manual.

9 terminals - new 2035 O. Right manual.

A+

A–

B+

B–

lead

motor

Red

Black

Red/

Wht

Green

Grn/Wht

White

6 Leads

Series

Connected

A+

A–

B+B–

lead

motor

Grn/Wht

White

Green

Red

Red/

Wht

Black

6 Leads

Center Tap

Connected

A+

A–

B+ B–

lead

motor

8 Leads

Series

Connected

Orange

Org/Wht

Blk/Wht

Black

Red

Red/

Wht

Yel/

Wht

Yellow

A+

A–

B+

B–

lead

motor

Orange

Org/

Wht

Blk/Wht

Black

Red

Red/Wht

Yel/

Wht

Yel

low

8 Leads

Parallel

Connected

Selecting Between Full and Half Step Operation

The top switch in the bank of DIP switches selects between

FULL and HALF step operation. The diagram shows the

drive in FULL step operation.

Setting Phase Current

The drive uses a combination or DIP switches to set the current. There is always a base

of current of 125 mA. To add to that, slide the appropriate switches toward their labels.

Example

Suppose you want to set the driver for 1.25 amps

per phase (1250 mA). You need the 125 mA base

current plus another 1000 and 125 mA.

1250 = 125 + 1000 +125

Slide the 125 and 1000 mA switches toward the labels

as shown in the gure.

HALF STEP

125

250

500

1000

logic

connector

STEP, DIR, EN

trimpots for adjusting

LED - indicates

DC power

oscillator speed, accel and

decel rates

(2035 O only)

mounting

hole (1 of 6)

power

connector

motor

connector

jumper for selecting

oscillator mode

(2035 O only)

switches for

selecting current,

idle current,

full or half stepping,

speed pot (2035 O)

connector for external

speed pot/signal

& tach output

(2035 O only)

A+

A–

B+ B–

lead

motor

Red

Blue

Yellow

White

4 Leads

COM

STEP

DIR

Inside 2035

2200

HALF STEP

125

250

500

1000

Quick Setup Guide

2035 & 2035-O

TO DOWNLOAD A FULL USER MANUAL PLEASE VISIT OUR WEBSITE

WWW.APPLIED-MOTION.COM

Connecting the Power Supply

12–35V

motor

supply

12-35 VDC

–

3A slow

blow

fuse

DO NOT REVERSE WIRES - THIS WILL DAMAGE THE DRIVE

+5 VDC

STEP–

STEP+

DIR–

DIR+

2035

COM

STEP

DIR

+5 VDC

STEP

DIR

2035

COM

STEP

DIR

1 2

Resumo do Conteúdo

Página 1 - 2035 & 2035-O

Flip OverConnecting the MotorSTEP motors have 4, 6 or 8 leads , these are wired to 4 connections on the drive in various combinations.Motors will per

Página 2 - Applied Motion Products, Inc

Check your wiring carefully before turning on the power supply!Current ReductionThe 2035 and 2035 O drives include a feature that automatically reduce

Modelos relacionados 2035O

Mais documentos para Hardware Applied-motion 2035

Para ver o documento Applied-motion 2035 Manual do Utilizador

Applied-motion 2035 Manual do Utilizador (8 páginas)

Comentários a estes Manuais

Sem comentários

Applied-motion 2035 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Applied-motion 2035. Applied Motion 2035 User Manual Manual do Utilizador

Resumo do Conteúdo

Modelos relacionados 2035O

Mais documentos para Hardware Applied-motion 2035

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Applied-motion 2035